Reloading Equipment & Accessories

The  Mr. Bullet Feeder by DAA, manufactured by Double-Alpha Academy under license by Rak Systems, is a professional, hi-tech version of the original.  It is lighter in weight and more compact than the previous models.  This new streamlined product is easier to install and set up, while retaining the same flawless performance and efficiency of the original design.

Conversion kits available in 9mm/38 super, 40 cal and 45 cal.

The PRIMER-PRO by Double-Alpha is a unique new approach to handling primers, and the solution reloaders have been waiting for!

As any reloader knows well, manually filling primer tubes can be the most time-consuming and aggravating step in the whole reloading process, and few good automated solutions exist.

Until now!

The PRIMER-PRO by Double-Alpha is an innovative patent-pending design which departs from the traditional vibratory bowl solution used by all other automated primer tube machines. The PRIMER-PRO uses a collator type solution where the primers are allowed to exit the bowl through 20 precisely formed channels, ONLY if they are orientated in the correct direction (Anvil side up). If they are Anvil down, they will not pass through the channel, and rather slide back into the bowl as their channel reaches the top of the rotation, to enter again later, correctly oriented.

This rejection-type design makes it practically impossible for a primer to enter the output channel if incorrectly orientated, making this device extremely reliable. During development, we ran many successful tests in which 100 tubes were filled (10,000 primers fed) without a single up-side-down primer!

As the primers slide down the covered output-chute, they pass through an optical sensor which counts them and stops the collator once 100 primers have been counted into the primer-tube. The electronic processor board also monitors the sensor and is programed to stop the collator if, for whatever reason, primers hang-up on the exit hole and stack up along the ramp. The collator will be stopped before the primers stack all the way up and jam the collator. In such a case, the LED will flash quickly to indicate there is a problem. Once cleared, pressing the start button again will allow the collator to run and the count will continue from where it was stopped. Or alternatively, a long press on the button will start the count a new.

One of the most innovative design solutions of the PRIMER-PRO is the Output Actuator Arm, which is activated by a lever system off the Timing Disk at the bottom of the Collator Assembly. This Output Actuator Arm slides the primers from the bottom of the ramp slide, moving them over to above the output hole, holding them there for a split second to ensure they are static, horizontal and stable, and then retracting to allow the primer to fall cleanly down into the awaiting primer tube. This dynamic solution for the exit hole greatly reduces the chance of primers hanging up while exiting into the tube, a problem common with other automated primer fillers.

The PRIMER-PRO is currently available only for Smaller Primers, and handles Small-Rifle or Small-Pistol Primers equally well. A Large primer version may be offered in the future.

One Magnetic Collar for a Dillon Primer Tube is included with the unit. A PRIMER TUBE IS NOT INCLUDED! Since the PRIMER-PRO can refill a single Primer Tube faster than you can use the previous 100 primers in any reloading press, only one tube is strictly necessary.

However additional Magnetic Collars can be purchased separately, for those who prefer to fill multiple tubes before starting their reloading session.

The unit is powder by a 12v DC power supply (dual voltage, 110-230), which ships including a suitable European and US prong set (included). The power cord is 2 meters (6ft) long, and includes an ON/OFF switch in the cable.

NOTE: Primer tube not included. 

The Double-Alpha PRIMAFILL is a semi-automatic primer-tube filling solution, able to quickly and easily fill both Small and Large primer tubes. It allows you to switch between Small and Large primers instantly, without tools or assembly.

The PRIMAFILL can be used with any primer tubes which have an 8mm outer diameter, such as Dillon, or DAA tubes. It does not require a custom adaptor piece fitted to the tube, as other competing products require. So using the PRIMAFILL, you will be able to fill all your primer tubes!

The Extra-Large flip-tray area is convenient when emptying large primer boxes, such as Federal and others. The tray is large enough for the entire box to fit over.

The PRIMAFILL is powered by a regular 9v battery (not included). A momentary ON switch falls naturally under your index finger as you hold the device for right hand use, with your thumb centered on top of the lid. Hold the button down as you feed the primers into the tube, and release as soon as the last primer vanishes down the exit hole. Since this action should take 20 seconds or less, one battery charge will last for many thousands of primers.

The spring-loaded orange latches incorporated into the output posts enable you to snap a tube into place, or remove it, instantly without any twists or turns, the latch falls naturally under your thumb: you press down on it as you insert the tube up, and  you press up on the latch as you extract the tube downwards. An Easy and natural apposing thumb action.

Primer tubes and battery are not included!

If you load on an XL650 you have probably encountered the annoyance of spent primers bouncing off the Spent Primer Cup and ending up on your reloading bench or floor.

The DAA XL650 Primer Output Tube Assembly puts an end to that problem by attaching directly over the spent primer exit window, and ensuring that spent primers have only one place to go – down the tube!

The assembly is supplied with a 120cm (4ft) long PVC flexible tube, which will allow you to collect your primers in a container or bottle resting on the floor or attached anywhere under your press.

The assemble includes:

- A 120cm (4ft) long PVC flexible tube

- A Delrin machined adaptor plate to fit to your XL650

- Two longer 8-32 screws to replace the original ones on your Dillon

The 1050 Spent Primer Chute™ replaces the plastic spent primer cup on the Dillon Super 1050 reloading press*. Spent primers are routed through clear PVC tubing into any convenient waste container. The 1050 Spent Primer Chute™ completely covers the spent primer ejection port, creating a fully enclosed pathway for spent primers … so they simply can't bounce out!

No more spent primers bouncing out and onto the floor when you reload!

Shellplate Bearing Kit Dillon Super 1050 adds a roller bearing on top of the shellplate to reduce powder spilling as the shellplate snaps into position. Run out is eliminated and this results in more consistent ammo.

Ultimate Bearing Kit Dillon XL 650 adds a roller bearing on top of the shellplate to reduce powder spilling as the shellplate snaps into position.  We also include a Camming Pin Bearing to replace the camming pin. Your press will run as smooth as silk with this kit. Our tough as nails phenolic low mass detent ball is included. Run out is eliminated and this results in more consistent ammo. The bearing also supports the shellplate resulting in better priming. It replaces screws with thumbscrews to speed up the adjustment of the press. Premium kit includes the very popular Shellplate Bearing Kit, thumbscrews for 3 powder measures and 3 powder measure adjustment knobs. This kit works with both new and old style powder measures.

Ultimate Shellplate Bearing Kit Dillon RL 550 B/C replaces the index sprocket with a modified sprocket that has the room required to install the shellplate bearing kit.  Run out is eliminated and this results in more consistent ammo. The bearing kit smoothens the action of the press, reducing powder spillage and increasing tactile feel while priming. Priming operation will be more consistent. Thumbscrews replace bolts to speed up the adjustment of the press. Thumbscrews for 3 powder measures and 3 powder measure adjustment knobs. This kit works with both new and old style powder measures.